How to Remove as well as Replace a Bath Tub.
How to Remove as well as Replace a Bath Tub.
Blog Article
Have you been interested in additional info on Installing A Bathtub?
Installing a bathtub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, as well as often, tiling abilities. Replacing an old tub with a new one is also a reasonably tough job. If the old tub is easily available, the project can move speedily; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and also set in the new one. See to it you have actually qualified on your own for the task and fit attempting it. Rather than employing a specialist to take control of a halfway-completed project, it is far better to think about using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This post will aid you set up a brand-new tub in your bathroom if you have actually already gotten a new bathtub and do not need to transform the setup of your previous water system pipelines.
Your devices and product list need to make up the following:
Getting ready for the Installment
First of all, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the needed position. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and examine all joints as well as new pipework for leaks as well as tighten them if required. Load the tub and additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the producer's user's manual. Tiling as well as securing around the bath tub must wait until the tub has been made use of at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washers are in area between the tap and also the sink. Secure the faucet in position with the producer supplied backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type must be attached to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bath as well as the tiling, causing complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, as well as are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to enable the motion experienced when the tub remains in use. The sealer can split relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave a comment down below. We would be delighted to hear your reactions about this page. In hopes to see you back again later on. For those who enjoyed reading our post plz remember to pass it around. Thanks a bunch for your time. Please come visit our site back soon.
Book With Us Today! Report this page